RHUB TM-510 Spécifications Page 276
- Page / 353
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
NOTE
TM 9-2350-311-34-1
10-1 WINTERIZATION KIT INSTALLATION —
CONTINUED
a. Installation — Continued
49
50
51
52
53
54
55
56
Connect coolant heater harness plug (123) to heater receptacle (1 24).
Connect harness lead (125) connector to heater coolant pump. Support harness lead with right headlight group
support strap.
Connect harness lead (circuit 402C) (126) to electric fuel pump connector.
Remove mounting screw (127) from coolant heater mounting bracket (20) and install harness ground lead
(128).
Remove two screws (129) and remove cover (130) from winterization kit heater control box (131 ).
Harness receptacle must face down. Reposition if necessary (para 10-2).
Remove two nuts (132) and two Iockwashers (133), place mounting bracket (134) on screws (135), and install
two nuts and two Iockwashers.
Install two screws (129) to cover (130).
Install mounting bracket (134), strap, control box (131), two flat washers (136), and two screws (137) to driver’s
compartment bulkhead tapping blocks (above engine compartment access door).
10-16
- TM 9-2350-311-34-1 1
- TABLE OF CONTENTS 9
- CONTENTS 11
- HOW TO USE THIS MANUAL 12
- WARNINGS, CAUTIONS, AND NOTES 13
- INITIAL SETUPS 13
- LOCATIONAL TERMS 14
- REFERENCING 14
- LOCATING INFORMATION 14
- CHAPTER 1 15
- INTRODUCTION 15
- 1-1 SCOPE 19
- 1-5 QUALITY ASSURANCE (QA) 20
- 1-8 WARRANTY INFORMATION 21
- 1-11.1 Electrical System 22
- Suspension 23
- Air Cleaner Assembly 23
- TM 9-2350-311-34-1 24
- Serial Number Locations 27
- 1-14 EQUIPMENT DATA 29
- 1-17/(1-18 blank) 31
- CHAPTER 2 33
- GENERAL HULL MAINTENANCE 33
- 2-8 REPLACEMENT OF PARTS 35
- 2-7 BALL AND ROLLER BEARINGS 35
- 2-10 WELDING 37
- SHAFTS, GEARS, AND BEARINGS 37
- 2-13 CLEANING 37
- 2-13 CLEANING — CONTINUED 38
- 2-14 PAINTING 39
- 2-15 LUBRICATION 39
- CHAPTER 3 41
- TROUBLESHOOTING 41
- SOLUTION OR REFERENCE 43
- 3-3 TROUBLESHOOTING CHART 46
- END OF TASK 47
- 9-2815-202-34) 49
- CHAPTER 4 57
- COMPONENTS 60
- COMPONENTS — CONTINUED 62
- 4-4 MASS RING AND COUPLER 76
- CHAPTER 5 83
- FUEL AND AIR INTAKE SYSTEMS 83
- 5-1 ELECTRIC FUEL PUMPS 84
- 5-1 ELECTRIC FUEL PUMPS — 88
- 5-2 FUEL TANKS 92
- 5-2 FUEL TANKS — CONTINUED 100
- TM9-2350-311-34-1 101
- 5-3 FUEL TANK PADS 102
- Installation 103
- INITIAL SETUP 104
- CLGP stowage area 106
- 5-5 AIR CLEANER BLOWER MOTORS 107
- C. Assembly — Continued 114
- 5-6 FUEL TANK HEAT SHIELD 118
- CHAPTER 6 119
- COOLING SYSTEM 119
- 6-1 UNIVERSAL JOINTS 120
- NOTE 123
- CONTINUED 130
- Assembly 134
- 6-17/(8-18 blank) 135
- CHAPTER 7 137
- ELECTRICAL SYSTEM 137
- (M109A2/M109A3) 140
- ENGINE MODEL 7083-7396 SHOWN 141
- (M109A4/M109A5) 142
- (ENGINE MODEL 7083-7396) 144
- FOLLOW-ON MAINTENANCE: 147
- (ENGINE MODEL 7083-7391) 156
- RELAY WIRING HARNESS 158
- Connect two connectors 173
- WIRING HARNESS 174
- Installation — Continued 182
- Installation- Continued 192
- 10 Connect connector (14) 194
- 11 Connect connector (6) 194
- (TM 9-2350-311-20-1) 195
- TM 92350-311 -34-1 206
- Disassembly 211
- TM 94350-311-34-1 221
- . Assembly 222
- CHAPTER 8 237
- 8-1 FINAL DRIVE ASSEMBLY 238
- SECTION Il. TRACK SUSPENSION 242
- CHAPTER 9 245
- HULL-RELATED COMPONENTS 245
- — CONTINUED 248
- 9-2 BILGE PUMP 252
- 9-2 BILGE PUMP — CONTINUED 254
- 9-3 DATA PLATES 260
- CHAPTER 10 261
- INITIAL SETUP 262
- 10-2 COOLANT HEATER 284
- 10-3 BLOWER MOTOR ASSEMBLY 296
- APPENDIX A 297
- REFERENCES 297
- A-8 TRAINING CIRCULARS 300
- APPENDIX B 301
- SECTION I. INTRODUCTION 302
- B-1 SCOPE 302
- B-2 EXPLANATION OF COLUMNS 302
- (0.9 L) kit: 304
- (17794) 1243-0001 304
- APPENDIX C 305
- TOOL IDENTIFICATION LIST 305
- C-1 EXPLANATION OF COLUMNS 306
- C-2 TOOL IDENTIFICATION LIST 307
- APPENDIX D 309
- Material 310
- ITEM 3 FABRICATED PAD 312
- APPENDIX E 315
- TORQUE LIMITS 315
- E-1 TORQUE LIMITS 316
- E-2 HOW TO USE TORQUE TABLE 316
- 50-50 Ib-ft (68-610 N•m) 318
- 0-170 Ib-ft (0-230 N•n) 318
- E-5 FASTENER GRADE 319
- APPENDIX F 321
- MANDATORY REPLACEMENT PARTS 321
- F-1 EXPLANATION OF COLUMNS 322
- F-5/(F-6 blank) 325
- D — CONTINUED 328
- T — CONTINUED 332
- PIN: 061100-000 352
- This fine document 353
© 2020, manymanuals.fr. Tous droits réservés | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels